CAMSWITCH QUAD is a network switch designed especially for security and IP video network installations.

CAMSWITCH is a four-plus-one-port 100BaseT Ethernet industrial network switch especially designed for networked video applications.

Four of the ports offer Power over Ethernet (PoE) for powering IP cameras via the CAT5 network cable. The fifth port on the opposite side of the case provides a convenient downstream network link for easy cable management.

CAMSWITCH Quad itself is powered by a 12V or 24V supply at the camera end. Wall-mountable, robust, compact and priced to compete with standard desktop switches which are less well-suited to real-world installations. Learn More

HIGHWIRE allows IP Network Cameras to communicate over existing co-axial video cables.

The latest addition to the HIGHWIRE range, this new model includes Power over Ethernet (PoE) for powering an IP camera via the CAT5 network cable.

The HIGHWIRE is powered as normal (usually from the legacy analog camera PSU), and then the PoE output runs the IP camera, making installation easy. 100% compatible with all HIGHWIRE versions.
Learn More

OUTREACH doubles, triples or even quadruples the normal 330ft (100m) CAT5 cable run length for 100BaseT networks. It forwards both Ethernet and PoE for another 330ft (100m) using a patent-pending power-processing scheme, and multiple units can be employed in series for even longer distances, with no degradation in network speed or latency. OUTREACH itself is powered by a PoE network switch (or PoE injector) and so requires no separate power connection in the middle of the cable, making it extremely easy to connect and power IP cameras two or three times further than previously possible without going to fibre or installing midspan power sources. Learn More

OUTSOURCE is a fully IEEE-compliant single channel POE midspan. It can be used to provide power for any compatible POE powered devices.

OUTSOURCE can be installed anywhere before the first OUTREACH in the chain, although normally it will be connected via a patch cable to a network switch with the longer cable running to the OUTREACH.

Note that OUTSOURCE is a passive device, it does not extend the signal so the total cable length on either side should not exceed 100m/330ft.

OUTSOURCE can safely be connected after a conventional POE switch. The switch will not enable power to the OUTSOURCE and the OUTSOURCE will only enable power to the OUTREACH. Learn More

OUTBREAK is a POE splitter that divides its POE network connection into a non-POE Ethernet signal and a 12 Volt 1 Amp auxiliary supply.

It can be used to power devices that are not POE compatible, devices which are compatible with older POE standards, or devices that are POE compatible but which require a shared 12V supply for other equipment.

Note that OUTBREAK is a maximum POE class device so must be used in conjunction with an OUTSOURCE. Learn More

8-port Gigabit Power Over Ethernet Midspan from Phihong:

• IEEE 802.3af Detection, Disconnect and overload Protection
• Full Power of 370W--15.4W per Port, No Power Management required
• Low Cost
• Full Protection OTP, OCP, OVP
• NIC Interface (Optional)
• 48V RPS Input (Optional)
• 10/100/1000 base T Compatible
• Cisco Legacy detection Learn More

16-port Gigabit Power Over Ethernet Midspan from Phihong:

• IEEE 802.3af Detection, Disconnect and overload Protection
• Full Power of 370W--15.4W per Port, No Power Management required
• Low Cost
• Full Protection OTP, OCP, OVP
• NIC Interface (Optional)
• 48V RPS Input (Optional)
• 10/100/1000 base T Compatible
• Cisco Legacy detection Learn More

24-port Gigabit Power Over Ethernet Midspan from Phihong:

• IEEE 802.3af Detection, Disconnect and overload Protection
• Full Power of 370W--15.4W per Port, No Power Management required
• Low Cost
• Full Protection OTP, OCP, OVP
• NIC Interface (Optional)
• 48V RPS Input (Optional)
• 10/100/1000 base T Compatible
• Cisco Legacy detection Learn More

• Fully Compliant detection, disconnect, over load and voltage control IEEE802.3af
• UNH IOL Test Report
• Diagnostic LEDs
• Full Protection OCP, OVP
• Non-Vented Case
• Gigabit Compatible Learn More

• Fully Compliant detection, disconnect, over load and voltage control IEEE802.3af
• UNH IOL Test Report
• Diagnostic LEDs
• Full Protection OCP, OVP
• Non-Vented Case
• Gigabit Compatible Learn More

• Fully Compliant detection, disconnect, over load and voltage control IEEE802.3af
• UNH IOL Test Report
• Diagnostic LEDs
• Full Protection OCP, OVP
• Non-Vented Case
• Gigabit Compatible Learn More

POE splitter with 5V DC output to suit cameras such as Axis 206 & 207. Learn More

POS-1000 POE Splitter; a POE splitter breaks-out the power component from the data cable at the device end of the network. Learn More

POI-2000 is a single-port POE power injector, also known as a midspan. Learn More

PIS-3000 is a combined delivery of one POI-2000 POE Injector unit and one POS-1000 Splitter unit.

This combination is all you need to use Power Over Ethernet to supply a single network peripheral which does not have built-in POE capability. Learn More